STD-302N/N-R Compliance assessment

STD-302N-R 434MHz/869MHz

Regulatory compliance of the STD-302N-R
The STD-302N-R is designed for embedding in other equipment. (Products incorporating the STD-302N-R are henceforward referred to as final products.)
The European regulation applicable to the STD-302N-R is the R&TTE Directive 1999/5/EC.The conformity assessment for the STD-302N-R was completed in accordance with the R&TTE Directive Annex III procedures.

Note: The STD-302N-R is intended to be used in all EU and EFTA countries.
For 434MHz band, there may be restrictions on the use of voice and audio applications in the following countries; FI, FR, HU, IT, LU, LI, CH.
For 869MHz band, there may be restrictions on the use of the equipment in the range of 869.3 to 869.4 MHz in the following countries; CY, CZ, FR, GR, IE, IT, LV, LT, PL, SI, SE.

Cautions related to regulatory compliance when embedding the STD-302N-R
1. Duty cycle
The STD-302N-R is designed to be used for the Non-Specific Short Range Devices defined in the ERC/REC 70-03 Annex 1.
The STD-302N-R continuously emits carrier signals when power is supplied. The user must design the final product to meet the requirements of the duty cycle as provided in the Regulatory parameters related to Annex 1 of the ERC/REC 70-03.
2. Antenna
The STD-302N-R is supplied without a dedicated antenna and the user is required to provide an antenna. The conformity assessment of the STD-302N-R was performed using Circuit Design’s standard antenna ANT-LEA-01(434MHz)/-02(869MHz) (1/4 lambda lead antenna), so we recommend using the ANT-LEA antenna or an antenna with equivalent characteristics and performance. If you use an antenna other than the recommended antenna, further radio conformity assessment may be required.
3. Supply voltage
The STD-302N-R should be used within the specified voltage range (3.0 V to 5.5 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the STD-302N-R should be mounted on the circuit boards of the final products and must be enclosed in the cases of the final products. No surface of the STD-302N-R should be exposed.

Conformity assessment of the final product
The manufacturer of the final product is responsible for the conformity assessment procedures of the final product in accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2 (Efficient use of the radio spectrum), the manufacturer of the final product incorporating the R&TTE assessed STD-302N-R will be exempted from its conformity assessment procedures. For details of how to use the conformity assessment of the STD-302N-R, please consult the relevant authorities or accredited certification bodies.

Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not necessary if the final product is used in the harmonized frequency band and is classified as Class-1 equipment. If the final product is not used in the harmonized frequency band and is classified as Class-2 equipment, the manufacturer of the final product has a duty to notify the relevant radio regulatory authorities in the countries where the final product is sold.
*NOTE: In case the STD-302N-R 434MHz is used with more than a 10% duty, notification of the final product will be required. A list of Class-1 equipment is available at http://www.ero.dk/

Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above mentioned information about the conformity assessment and notification of the final product. Directives, technical standards, principles of operation and the like may be interpreted differently by the authorities in each country. Also the national laws and restrictions vary with the country. In case of doubt or uncertainty, we recommend that you check with the authorities or official certification organizations of the relevant countries.

STD-302N-R 419MHz

STD-302N-R 419 MHz was designed to be installed in radio equipment for use in China. However this product has not been assessed for conformity with the appropriate local regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of 'STD-302N-R 419MHz operation guide'.

STD-302N-R 447MHz

STD-302N-R 447 MHz was designed to be installed in radio equipment for use in Korea. However this product has not been assessed for conformity with the appropriate local regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of 'STD-302N-R 447MHz operation guide'.

STD-302N-R 429MHz

STD-302N-R 429 MHz was designed to be installed in radio equipment for use in Japan and to meet the specifications of STD-T67. However this product has not been assessed for conformity with the regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
You can find more Japanese regulatory information at Compliance Assessment.

STD-302N-R 458MHz

STD-302N-R 458 MHz was designed to be installed in radio equipment for use in UK and to meet the specifications of EN300 220-1 V.1.3.1. However this product has not been assessed for conformity with the regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of 'STD-302N-R 458MHz operation guide'.

STD-302N-R 335MHz

STD-302N-R 335 MHz was designed to be installed in crane remote control systems for use in India. However this product has not been assessed for conformity with the appropriate local regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance. For more information, refer to the regulatory compliance information of 'STD-302N-R 335 MHz operation guide'.