| CDP-TX-04S-R
434MHz / 869MHz |
 |
Regulatory compliance of the CDP-TX-04S-R
The CDP-TX-04S-R is designed for embedding in other equipment.
(Products incorporating the CDP-TX-04S-R are henceforward referred
to as final products.)
The European regulation applicable to the CDP-TX-04S-R is the R&TTE
Directive 1999/5/EC. The conformity assessment for the
CDP-TX-04S-R was completed in accordance with the R&TTE Directive
Annex III procedures.
Cautions related to regulatory compliance when embedding the
CDP-TX-04S-R
1. Duty cycle
The CDP-TX-04S-R is designed to be used for the Non-Specific Short
Range Devices defined in the ERC/REC 70-03 Annex 1.
The CDP-TX-04S-R continuously emits carrier signals when power is
supplied. The user must design the final product to meet the
requirements of the duty cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC 70-03.
2. Antenna
The CDP-TX-04S-R is supplied without a dedicated antenna and the
user is required to provide an antenna. The conformity assessment
of the CDP-TX-04S-R was performed using Circuit Design’s standard
antenna ANT-LEA-01 (1/4 lambda lead antenna), so we recommend
using the ANT-LEA-01 antenna or an antenna with equivalent
characteristics and performance. For details about our standard
antenna, refer to the “Options”
page in this web site or contact us. If you use an antenna other
than the recommended antenna, further radio conformity assessment
may be required.
3. Supply voltage
The CDP-TX-04S-R should be used within the specified voltage range
(2.2 V to 5.5 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the
CDP-TX-04S-R should be mounted on the circuit board of the final
product, and must be enclosed in the case of the final product. No
surface of the CDP-TX-04S-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final product incorporating the R&TTE assessed CDP-TX-04S-R will
be exempted from its conformity assessment procedures. For details
of how to use the conformity assessment of the CDP-TX-04S-R,
please consult the relevant authorities or accredited
certification bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not
necessary if the final product is used in the harmonized frequency
band and is classified as Class-1 equipment. If the final product
is not used in the harmonized frequency band and is classified as
Class-2 equipment, the manufacturer of the final product has a
duty to notify the relevant radio regulatory authorities in the
countries where the final product is sold.
*NOTE: In case the CDP-TX-04S-R 434.075 MHz is used with more than
a 10% duty cycle, notification of the final product will be
required. A list of Class-1 equipment is available at
http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries.
|
| CDP-RX-03BS-R
434MHz / CDP-RX-03AS-R 869MHz |
|
 |
Regulatory compliance of the CDP-RX-03BS-R and the
CDP-RX-03AS-R
The CDP-RX-03BS-R and the CDP-RX-03AS-R are designed for embedding
in other equipment. (Products incorporating the CDP-RX-03BS-R and
the CDP-RX-03AS-R are henceforward referred to as final products.)
The European regulation applicable to these modules is the R&TTE
Directive 1999/5/EC. The conformity assessment for the
CDP-RX-03BS-R and the CDP-RX-03AS-R was completed in accordance
with the R&TTE Directive Annex II procedures.
Note: The CDP-RX-03BS-R and the CDP-RX-03AS-R are intended to be
used in all EU and EFTA countries.
For 434 MHz band, there may be restrictions on the use of voice
and audio applications in the following countries; FI, FR, HU, IT,
LU, LI, CH.
Cautions related to regulatory compliance when embedding the
CDP-RX-03BS-R and the CDP-RX-03AS-R
Enclosure
To fulfill the requirements of EMC and safety requirements, the
CDP-RX-03BS-R and the CDP-RX-03AS-R should be mounted on the
circuit board of the final product, and must be enclosed in the
case of the final product. No surface of the CDP-RX-03BS-R and the
CDP-RX-03AS-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final products incorporating the R&TTE assessed CDP-RX-03BS-R and
the CDP-RX-03AS-R will be exempted from its conformity assessment
procedures. For details of how to use the conformity assessment of
the CDP-RX-03BS-R and the CDP-RX-03AS-R, please consult the
relevant authorities or accredited certification bodies.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries.
|
|
|
|
|
|
|
